Rain-Shield Garden Hose & Nozzle Valet

A wall-mounted hose hanger with a drain-holed nozzle holster and a sloped drip tray built in, so the hose, its spray nozzle, and the puddle it leaves all have one spot on the wall instead of three.

Date: 2026-10-24 Category: Outdoor and Garden Modeling difficulty: Intermediate Estimated print: ~9 h total · ~155 g PETG (estimate) Suggested price: $20–$32 printed · $7 digital file (estimate) Status: Concept

Description

The main piece is a wall backplate with a curved arm molded into its face — loop the hose over the arm and it hangs clear of the ground. A second part, a tapered cup, slides onto a dovetail rail to the side of the arm and holds the spray nozzle head-down, with a drain hole at its tip so water runs out instead of sitting in the cup and freezing in winter. A third part, a shallow sloped tray, slides onto rails near the bottom of the backplate and catches whatever drips off the coiled hose before it reaches the siding, directing it out a small spout at the low corner instead of down the wall.

Each piece clips on separately, so a buyer who only wants the hose arm can skip the holster and tray, and a buyer who wants all three gets a kit that assembles in under five minutes with no glue.

Why it sells

A 3D-printed wall-mounted hose holder is already an active Etsy listing, pitched specifically on keeping the hose off the ground and "reducing the risk of kinks, tangles, and damage" (Etsy listing). The broader hose-holder and hose-reel categories on Etsy carry many active listings, and a separate 3D-printable hose connector shows buyers are comfortable with printed parts touching their outdoor hose setup specifically (Etsy market page, Etsy market page, Etsy listing). A SlashGear roundup of 3D-printed camping and backpacking gadgets, and a wilderness survival kit listing, both point to steady demand for printed gear that solves a specific small outdoor annoyance rather than replacing a whole product category (SlashGear, Etsy listing).

The existing hose-holder listings researched here are a hook and nothing else. None of them address where the spray nozzle goes or where the drip lands once the hose is hung — this design treats the hose, the nozzle, and the drip as one problem.

Who buys it

Homeowners and renters with a garden hose and no good place to put it: beside an outdoor spigot, on a shed wall, or on a deck post. It's a small, low-cost impulse add to a hose or sprinkler purchase, and it fits the same local-market and Etsy-storefront channels the comparable hose holders already sell through.

Design overview

• One backplate with the hanging arm molded in, so the core product is a single printed part
• A separate nozzle holster that drains instead of pooling water, unlike a plain hook or clip
• A sloped drip tray that routes water to one spout corner instead of letting it run down the wall
• Slide-on dovetail and rail joints for the add-on pieces, no glue, no screws beyond wall mounting
• Keyhole slots sized for standard wood screws, so it hangs the same way a picture frame does
• PETG specified over PLA for outdoor UV and moisture exposure

Dimensions

Parts list

Hardware and non-printed parts

• #8 × 38 mm wood screw ×2 — through the backplate's keyhole slots into the wall or post
• Plastic wall anchor ×2 — for mounting into siding or drywall rather than solid wood

Fits and tolerances

Modeling guide

Origin at the backplate's bottom-left-back corner, the point that touches the wall; +X to the right, +Y outward from the wall, +Z up.

Backplate with hook arm

1. Sketch on XZ at Y=0: rectangle 200 (X) × 150 (Z), corner radius 10. Extrude +Y by 8 (backplate thickness).
2. From a start point at X=100, Z=110 on the front face, sweep a 20 × 15 mm oval profile along a path: straight 70 mm in +Y, then a 180° arc of radius 35 mm curving downward and back toward the wall, ending at approximately Y=20, Z=70. Merge the sweep with the backplate.
3. At the arm's open tip, add a small upward lip, 10 mm, and chamfer the tip edge 3 mm so a looped hose doesn't slide off easily.
4. Cut two keyhole slots: at (X=30, Z=130) and (X=170, Z=130), each a 10 mm diameter through-hole opening into a 5 mm-wide slot extending up to Z=145.
5. On the front face, right side, extrude a dovetail rail boss, trapezoid cross-section 10 mm wide at the base narrowing to 8 mm, 6 mm deep, from X=165 to X=175, Z=20 to Z=120.
6. On the front face, lower section, extrude two parallel horizontal rails (trapezoid, 8 mm wide narrowing to 6 mm, 5 mm deep) at X=16–24 and X=176–184, projecting 20 mm in +Y from the backplate face.
7. At the back end of each drip-tray rail (near Y=8), add a 4 mm stop-tab boss to halt the tray's slide.
8. Fillet all exterior edges 2 mm.

Nozzle holster

1. Sketch a 55 mm diameter circle at Z=110 (top opening). Loft down to a 30 mm diameter circle at Z=5.
2. Shell the lofted body, wall thickness 2.5 mm, leaving the top open.
3. At the bottom tip (Z=0), cut an 8 mm diameter drain hole through the floor.
4. On the back face, extrude a dovetail socket groove (matching the backplate rail minus 0.2 mm per side), 10 mm tall × 6 mm deep, running the holster's full 110 mm height.
5. Fillet the top rim 2 mm.

Drip tray

1. Sketch on XY: rectangle 180 × 90, corner radius 6. Extrude the floor 6 mm thick, sloped 5° from Z=6 at the back edge (Y=90) down to Z=0 at the front-right corner (X=170, Y=5).
2. Extrude a perimeter wall 15 mm tall × 2.5 mm thick around the sloped floor, open where the drain spout sits.
3. At the low corner, extrude a drain spout 10 mm diameter, protruding 15 mm beyond the wall, bore 8 mm.
4. On the back edge, cut two rail-groove channels, 8.4 mm wide × 5.4 mm deep, running 20 mm, matching the backplate's rail spacing.
5. Fillet all exterior edges 2 mm.

Print settings

Assembly

1. Mark and drill two screw points 140 mm apart at the mounting height; drive the screws partway in.
2. Hang the backplate on the screws through its keyhole slots.
3. Slide the nozzle holster down onto the backplate's dovetail rail until it stops.
4. Slide the drip tray onto the backplate's lower rails until it hits the stop tabs.
5. Loop the hose over the arm, and hang the spray nozzle head-down in the holster.

Variants and upsells

• A wider backplate (260 mm) with a second hook arm for two hoses side by side
• A post-mount base plate accessory for mounting on a round fence post instead of a flat wall
• A color-matched kit (terracotta, forest green, charcoal) to blend with common siding and fence colors
• A smaller version scaled for a coiled-nozzle-only mount, sold cheaper for apartment patios with no full hose to hang

Selling and distribution

Sell on Etsy next to the existing wall-mounted hose holder listings, leading with the drain-holed nozzle holster and drip tray as the feature the competing single-hook listings don't have. Price the full three-piece kit at $20–$32 to cover PETG, about 9 hours of machine time, and margin over the plain-hook competitors; offer the backplate alone at a lower price for buyers who just want the hook. License the files for commercial use, matching the commercial Etsy sellers already active in this category.

Listing keywords: garden hose holder, wall mount hose hanger, hose and nozzle holder, outdoor hose storage, drip tray hose mount, no-kink hose hanger, garden wall organizer, weatherproof hose holder.

Risks and IP notes

• The swept hook arm has a curved underside that can sag without support; the minimal auto-support called out above is there specifically for that overhang, not optional.
• PLA embrittles and discolors outdoors within a season; this design only holds up as described in PETG or ASA, and the listing should say so to avoid returns from buyers who print it in PLA.
• Plain wall-mounted hose hooks are common prior art; the drain-holed holster and sloped drip tray are the differentiating claims, not the hook shape itself.
• A full hose's weight loaded onto the arm concentrates stress at the arm-to-backplate junction; the design relies on the 20 mm arm cross-section and should not be thinned down in a "lightweight" variant without re-checking that joint.

Resource links

• Wall Mounted Hose Holder: 3D Printed Garden Hose Tidy, Etsy — direct bestseller comparable, same core pitch
• Garden Hose Holder, Etsy market page — category breadth
• Hose Reels, Etsy market page — adjacent category showing buyer demand for hose management generally
• 3D Printable Hose Connector, Etsy — shows buyer comfort with printed parts on hose hardware
• 5 Useful 3D Printed Gadgets For Camping And Backpacking, SlashGear — editorial signal for printed outdoor-gadget demand
• 3D Printed Wilderness Camping Hiking Hunting Survival Kit, Etsy — adjacent outdoor 3D-printed gear listing